Wind SMS Suite SupraThermal Ion Composition Spectrometer (SMS/STICS) Ion Velocity Distribution Functions (VDFs), Level 2 (L2), 3-minute Data in Solar Wind

The data include Wind STICS 3-minute 3D velocity distribution functions (VDFs) in three units (phase space density, differential number flux and counts), together with their statistical errors, for selected ion species using triple coincidence (H+, He+, He2+, C5+, O+, O6+, and Fe10+) and double coincidence (H+, He+, He2+, O+, O6+) measurements in the solar wind. For details, see https://spdf.gsfc.nasa.gov/pub/data/wind/documents/wind_stics_lv2_release_notes_revD.pdf.
The Suprathermal Ion Composition Spectrometer (STICS) is a time of flight (TOF) plasma mass spectrometer, capable of identifying mass and mass per charge for incident ions up to 200 keV/e. It uses an electrostatic analyzer to admit ions of a particular energy per charge (E/Q) into the TOF chamber. The E/Q voltage is stepped through 32 values, sitting at each value for approximately 24 sec., to measure ions over the full E/Q range of 6 - 200 keV/e. Ions then pass through a carbon foil and TOF chamber, before finally impacting on a solid-state detector (SSD) for energy measurement. STICS combines these three measurements of E/Q, TOF and residual energy, producing PHA words. This triple-coincidence technique greatly improves the signal to noise ratio in the data. Measurements of E/Q and TOF without residual energy also produce PHA words. These double-coincidence measurements are characterized by better statistics since ions whose energy does not allow them to be registered by the SSD can still be counted in double-coincidence measurements. However, ion identification in double-coincidence measurements are limited to a select number of ions that are well separated in E/Q - TOF space.  The STICS instrument provides full 3D velocity distribution functions, through a combination of multiple telescopes and spacecraft spin. The instrument includes 3 separate TOF telescopes that view 3 separate latitude sectors, as shown in Figure 1 (https://spdf.gsfc.nasa.gov/pub/data/wind/documents/wind_stics_lv2_release_notes_revD.pdf). In addition, the WIND spacecraft spins, allowing the 3 telescopes to trace out a nearly 4π steradian viewing area. The longitudinal sectors are shown in Figure 2. The solar direction is in sectors 8-10 while the earthward direction is in sectors 0-2.

Please acknowledge the Principal Investigator S. T. Lepri for use of the Data

Lepri, Susan T.; Raines, Jim M.; Ploof, Keeling C.; Tracy, Patrick J.; Gruesbeck, Jacob R.; Eddy, Tyler J.; Thomas, Jonathan W.

Please acknowledge the Principal Investigator S. T. Lepri. Please acknowledge the Data Providers and CDAWeb when using these Data.

[no plot] Full 3-D VDF in phase space density for triple coincidence H+.

* Column 1 Labels from SECTOR_ANGLE: ["Sector 0 202.5 deg","Sector 1 180 deg","Sector 2 157.5 deg","Sector 3 135 deg","Sector 4 112.5 deg","Sector 5 90 deg","Sector 6 67.5 deg","Sector 7 45d eg","Sector 8 22.5 deg","Sector 9 0 deg","Sector 10 337.5deg","Sector 11 315 deg","Sector 12 292.5deg","Sector 13 270 deg","Sector 14 247.5deg","Sector 15 225 deg"].
* Column 2 Labels from TELESCOPE_ANGLE: ["Telescope 1 +53deg","Telescope 2 0deg","Telescope 3 -53deg"].

Phase space density value triple coincidence H+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_hplus.

Phase space density value triple coincidence H+ - summed over telescope and eoq (sorted sector)

* SPDF:summed and sorted for spectrogram plot
This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_hplus_sum1, SECTOR_angle.

Phase space density value triple coincidence H+ (Telescope 2).

* Column 1 Labels from SECTOR_ANGLE: ["Sector 0 202.5 deg","Sector 1 180 deg","Sector 2 157.5 deg","Sector 3 135 deg","Sector 4 112.5 deg","Sector 5 90 deg","Sector 6 67.5 deg","Sector 7 45d eg","Sector 8 22.5 deg","Sector 9 0 deg","Sector 10 337.5deg","Sector 11 315 deg","Sector 12 292.5deg","Sector 13 270 deg","Sector 14 247.5deg","Sector 15 225 deg"]

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_hplus.

[no plot] Error in velocity distribution function value triple coincidence H+.

[no plot] Full 3-D VDF in counts for triple coincidence H+.

Counts for triple coincidence H+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_hplus.

Counts for triple coincidence H+ - summed over telescope and eoq (sorted sector)

* SPDF: summed and sorted for spectrogram plot
This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_hplus_sum1, SECTOR_angle.

Counts for triple coincidence H+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_hplus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence H+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence H+.

Differential flux, dJ/dE triple coincidence H+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_hplus.

Differential flux, dJ/dE triple coincidence H+ - summed over telescope and eoq (sorted sector)

* SPDF: summed and sorted for spectrogram
This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_hplus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence H+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_hplus.

[no plot] Error in the differential flux value triple coincidence H+.

[no plot] Full 3-D VDF in phase space density for triple coincidence He+.

Phase space density value triple coincidence He+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_heplus.

Phase space density value triple coincidence He+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_heplus_sum1, SECTOR_angle.

Phase space density value triple coincidence He+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_heplus.

[no plot] Error in velocity distribution function value triple coincidence He+.

[no plot] Full 3-D VDF in counts for triple coincidence He+.

Counts for triple coincidence He+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_heplus.

Counts for triple coincidence He+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_heplus_sum1, SECTOR_angle.

Counts for triple coincidence He+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_heplus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence He+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence He+.

Differential flux, dJ/dE triple coincidence He+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_heplus.

Differential flux, dJ/dE triple coincidence He+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_heplus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence He+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_heplus.

[no plot] Error in the differential flux value triple coincidence He+.

[no plot] Full 3-D VDF in phase space density for triple coincidence He2+.

Phase space density value triple coincidence He2+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_he2plus.

Phase space density value triple coincidence He2+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_he2plus_sum1, SECTOR_angle.

Phase space density value triple coincidence He2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_he2plus.

[no plot] Error in velocity distribution function value triple coincidence He2+.

[no plot] Full 3-D VDF in counts for triple coincidence He2+.

Counts for triple coincidence He2+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_he2plus.

Counts for triple coincidence He2+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_he2plus_sum1, SECTOR_angle.

Counts for triple coincidence He2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_he2plus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence He2+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence He2+.

Differential flux, dJ/dE triple coincidence He2+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_he2plus.

Differential flux, dJ/dE triple coincidence He2+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_he2plus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence He2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_he2plus.

[no plot] Error in the differential flux value triple coincidence He2+.

[no plot] Full 3-D VDF in phase space density for triple coincidence O+.

Phase space density value triple coincidence O+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_oplus.

Phase space density value triple coincidence O+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_oplus_sum1, SECTOR_angle.

Phase space density value triple coincidence O+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_oplus.

[no plot] Error in velocity distribution function value triple coincidence O+.

[no plot] Full 3-D VDF in counts for triple coincidence O+.

Counts for triple coincidence O+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_oplus.

Counts for triple coincidence O+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_oplus_sum1, SECTOR_angle.

Counts for triple coincidence O+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_oplus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence O+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence O+.

Differential flux, dJ/dE triple coincidence O+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_oplus.

Differential flux, dJ/dE triple coincidence O+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_oplus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence O+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_oplus.

[no plot] Error in the differential flux value triple coincidence O+.

[no plot] Full 3-D VDF in phase space density for triple coincidence O6+.

Phase space density value triple coincidence O6+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_o6plus.

Phase space density value triple coincidence O6+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_o6plus_sum1, SECTOR_angle.

Phase space density value triple coincidence O6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_o6plus.

[no plot] Error in velocity distribution function value triple coincidence O6+.

[no plot] Full 3-D VDF in counts for triple coincidence O6+.

Counts for triple coincidence O6+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_o6plus.

Counts for triple coincidence O6+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_o6plus_sum1, SECTOR_angle.

Counts for triple coincidence O6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_o6plus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence O6+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence O6+.

Differential flux, dJ/dE triple coincidence O6+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_o6plus.

Differential flux, dJ/dE triple coincidence O6+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_o6plus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence O6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_o6plus.

[no plot] Error in the differential flux value triple coincidence O6+.

[no plot] Full 3-D VDF in phase space density for triple coincidence C5+.

Phase space density value triple coincidence C5+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_c5plus.

Phase space density value triple coincidence C5+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_c5plus_sum1, SECTOR_angle.

Phase space density value triple coincidence C5+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_c5plus.

[no plot] Error in velocity distribution function value triple coincidence C5+.

[no plot] Full 3-D VDF in counts for triple coincidence C5+.

Counts for triple coincidence C5+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_c5plus.

Counts for triple coincidence C5+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_c5plus_sum1, SECTOR_angle.

Counts for triple coincidence C5+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_c5plus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence C5+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence C5+.

Differential flux, dJ/dE triple coincidence C5+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_c5plus.

Differential flux, dJ/dE triple coincidence C5+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_c5plus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence C5+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_c5plus.

[no plot] Error in the differential flux value triple coincidence C5+.

[no plot] Full 3-D VDF in phase space density for triple coincidence Fe10+.

Phase space density value triple coincidence Fe10+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_tc_fe10plus.

Phase space density value triple coincidence Fe10+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_tc_fe10plus_sum1, SECTOR_angle.

Phase space density value triple coincidence Fe10+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_fe10plus.

[no plot] Error in velocity distribution function value triple coincidence Fe10+.

[no plot] Full 3-D VDF in counts for triple coincidence Fe10+.

Counts for triple coincidence Fe10+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_tc_fe10plus.

Counts for triple coincidence Fe10+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_tc_fe10plus_sum1, SECTOR_angle.

Counts for triple coincidence Fe10+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_tc_fe10plus.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence Fe10+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence Fe10+.

Differential flux, dJ/dE triple coincidence Fe10+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_tc_fe10plus.

Differential flux, dJ/dE triple coincidence Fe10+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_tc_fe10plus_sum1, SECTOR_angle.

Differential flux, dJ/dE triple coincidence Fe10+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_fe10plus.

[no plot] Error in the differential flux value triple coincidence Fe10+.

[no plot] Full 3-D VDF in phase space density for triple coincidence C+.

Phase space density value triple coincidence C+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_cplus.

[no plot] Error in velocity distribution function value triple coincidence C+.

[no plot] Full 3-D VDF in counts for triple coincidence C+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence C+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence C+.

Differential flux, dJ/dE triple coincidence C+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_cplus.

[no plot] Error in the differential flux value triple coincidence C+.

[no plot] Full 3-D VDF in phase space density for triple coincidence N+.

Phase space density value triple coincidence N+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_nplus.

[no plot] Error in velocity distribution function value triple coincidence N+.

[no plot] Full 3-D VDF in counts for triple coincidence N+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence N+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence N+.

Differential flux, dJ/dE triple coincidence N+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_nplus.

[no plot] Error in the differential flux value triple coincidence N+.

[no plot] Full 3-D VDF in phase space density for triple coincidence O2+.

Phase space density value triple coincidence O2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_o2plus.

[no plot] Error in velocity distribution function value triple coincidence O2+.

[no plot] Full 3-D VDF in counts for triple coincidence O2+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence O2+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence O2+.

Differential flux, dJ/dE triple coincidence O2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_o2plus.

[no plot] Error in the differential flux value triple coincidence O2+.

[no plot] Full 3-D VDF in phase space density for triple coincidence O7+.

Phase space density value triple coincidence O7+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_o7plus.

[no plot] Error in velocity distribution function value triple coincidence O7+.

[no plot] Full 3-D VDF in counts for triple coincidence O7+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence O7+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence O7+.

Differential flux, dJ/dE triple coincidence O7+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_o7plus.

[no plot] Error in the differential flux value triple coincidence O7+.

[no plot] Full 3-D VDF in phase space density for triple coincidence O8+.

Phase space density value triple coincidence O8+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_o8plus.

[no plot] Error in velocity distribution function value triple coincidence O8+.

[no plot] Full 3-D VDF in counts for triple coincidence O8+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence O8+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence O8+.

Differential flux, dJ/dE triple coincidence O8+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_o8plus.

[no plot] Error in the differential flux value triple coincidence O8+.

[no plot] Full 3-D VDF in phase space density for triple coincidence C4+.

Phase space density value triple coincidence C4+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_c4plus.

[no plot] Error in velocity distribution function value triple coincidence C4+.

[no plot] Full 3-D VDF in counts for triple coincidence C4+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence C4+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence C4+.

Differential flux, dJ/dE triple coincidence C4+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_c4plus.

[no plot] Error in the differential flux value triple coincidence C4+.

[no plot] Full 3-D VDF in phase space density for triple coincidence C6+.

Phase space density value triple coincidence C6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_c6plus.

[no plot] Error in velocity distribution function value triple coincidence C6+.

[no plot] Full 3-D VDF in counts for triple coincidence C6+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence C6+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence C6+.

Differential flux, dJ/dE triple coincidence C6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_c6plus.

[no plot] Error in the differential flux value triple coincidence C6+.

[no plot] Full 3-D VDF in phase space density for triple coincidence Fe8+.

Phase space density value triple coincidence Fe8+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_fe8plus.

[no plot] Error in velocity distribution function value triple coincidence Fe8+.

[no plot] Full 3-D VDF in counts for triple coincidence Fe8+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence Fe8+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence Fe8+.

Differential flux, dJ/dE triple coincidence Fe8+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_fe8plus.

[no plot] Error in the differential flux value triple coincidence Fe8+.

[no plot] Full 3-D VDF in phase space density for triple coincidence Fe9+.

Phase space density value triple coincidence Fe9+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_fe9plus.

[no plot] Error in velocity distribution function value triple coincidence Fe9+.

[no plot] Full 3-D VDF in counts for triple coincidence Fe9+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence Fe9+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence Fe9+.

Differential flux, dJ/dE triple coincidence Fe9+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_fe9plus.

[no plot] Error in the differential flux value triple coincidence Fe9+.

[no plot] Full 3-D VDF in phase space density for triple coincidence Fe16+.

Phase space density value triple coincidence Fe16+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_tc_fe16plus.

[no plot] Error in velocity distribution function value triple coincidence Fe16+.

[no plot] Full 3-D VDF in counts for triple coincidence Fe16+.

[no plot] Error in counts estimated assuming Poisson statistics triple coincidence Fe16+.

[no plot] Full 3-D VDF differential flux, dJ/dE triple coincidence Fe16+.

Differential flux, dJ/dE triple coincidence Fe16+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_tc_fe16plus.

[no plot] Error in the differential flux value triple coincidence Fe16+.

[no plot] Full 3-D VDF in phase space density for double coincidence H+.

Phase space density value double coincidence H+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_dc_hplus.

Phase space density value double coincidence H+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_dc_hplus_sum1, SECTOR_angle.

Phase space density value double coincidence H+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_dc_hplus.

[no plot] Error in velocity distribution function value double coincidence H+.

[no plot] Full 3-D VDF in counts for double coincidence H+.

Counts for double coincidence H+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_dc_hplus.

Counts for double coincidence H+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_dc_hplus_sum1, SECTOR_angle.

Counts for double coincidence H+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_dc_hplus.

[no plot] Error in counts estimated assuming Poisson statistics double coincidence H+.

[no plot] Full 3-D VDF differential flux, dJ/dE double coincidence H+.

Differential flux, dJ/dE double coincidence H+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_dc_hplus.

Differential flux, dJ/dE double coincidence H+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_dc_hplus_sum1, SECTOR_angle.

Differential flux, dJ/dE double coincidence H+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_dc_hplus.

[no plot] Error in the differential flux value double coincidence H+.

[no plot] Full 3-D VDF in phase space density for double coincidence He+.

Phase space density value double coincidence He+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_dc_heplus.

Phase space density value double coincidence He+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_dc_heplus_sum1, SECTOR_angle.

Phase space density value double coincidence He+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_dc_heplus.

[no plot] Error in velocity distribution function value double coincidence He+.

[no plot] Full 3-D VDF in counts for double coincidence He+.

Counts for double coincidence He+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_dc_heplus.

Counts for double coincidence He+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_dc_heplus_sum1, SECTOR_angle.

Counts for double coincidence He+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_dc_heplus.

[no plot] Error in counts estimated assuming Poisson statistics double coincidence He+.

[no plot] Full 3-D VDF differential flux, dJ/dE double coincidence He+.

Differential flux, dJ/dE double coincidence He+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_dc_heplus.

Differential flux, dJ/dE double coincidence He+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_dc_heplus_sum1, SECTOR_angle.

Differential flux, dJ/dE double coincidence He+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_dc_heplus.

[no plot] Error in the differential flux value double coincidence He+.

[no plot] Full 3-D VDF in phase space density for double coincidence He2+.

Phase space density value double coincidence He2+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_dc_he2plus.

Phase space density value double coincidence He2+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_dc_he2plus_sum1, SECTOR_angle.

Phase space density value double coincidence He2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_dc_he2plus.

[no plot] Error in velocity distribution function value double coincidence He2+.

[no plot] Full 3-D VDF in counts for double coincidence He2+.

Counts for double coincidence He2+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_dc_he2plus.

Counts for double coincidence He2+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_dc_he2plus_sum1, SECTOR_angle.

Counts for double coincidence He2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_dc_he2plus.

[no plot] Error in counts estimated assuming Poisson statistics double coincidence He2+.

[no plot] Full 3-D VDF differential flux, dJ/dE double coincidence He2+.

Differential flux, dJ/dE double coincidence He2+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_dc_he2plus.

Differential flux, dJ/dE double coincidence He2+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_dc_he2plus_sum1, SECTOR_angle.

Differential flux, dJ/dE double coincidence He2+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_dc_he2plus.

[no plot] Error in the differential flux value double coincidence He2+.

[no plot] Full 3-D VDF in phase space density for double coincidence O+.

Phase space density value double coincidence O+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_dc_oplus.

Phase space density value double coincidence O+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_dc_oplus_sum1, SECTOR_angle.

Phase space density value double coincidence O+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_dc_oplus.

[no plot] Error in velocity distribution function value double coincidence O+.

[no plot] Full 3-D VDF in counts for double coincidence O+.

Counts for double coincidence O+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_dc_oplus.

Counts for double coincidence O+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_dc_oplus_sum1, SECTOR_angle.

Counts for double coincidence O+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_dc_oplus.

[no plot] Error in counts estimated assuming Poisson statistics double coincidence O+.

[no plot] Full 3-D VDF differential flux, dJ/dE double coincidence O+.

Differential flux, dJ/dE double coincidence O+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_dc_oplus.

Differential flux, dJ/dE double coincidence O+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_dc_oplus_sum1, SECTOR_angle.

Differential flux, dJ/dE double coincidence O+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_dc_oplus.

[no plot] Error in the differential flux value double coincidence O+.

[no plot] Full 3-D VDF in phase space density for double coincidence O6+.

Phase space density value double coincidence O6+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: DF_dc_o6plus.

Phase space density value double coincidence O6+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: DF_dc_o6plus_sum1, SECTOR_angle.

Phase space density value double coincidence O6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_dc_o6plus.

[no plot] Error in velocity distribution function value double coincidence O6+.

[no plot] Full 3-D VDF in counts for double coincidence O6+.

Counts for double coincidence O6+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: counts_dc_o6plus.

Counts for double coincidence O6+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: counts_dc_o6plus_sum1, SECTOR_angle.

Counts for double coincidence O6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: counts_dc_o6plus.

[no plot] Error in counts estimated assuming Poisson statistics double coincidence O6+.

[no plot] Full 3-D VDF differential flux, dJ/dE double coincidence O6+.

Differential flux, dJ/dE double coincidence O6+ - summed over telescope and sector

This parameter is virtual. It is calculated by calling the function SPDF_SUM_OVER_COL_ROW with the following input parameters: dJ_dc_o6plus.

Differential flux, dJ/dE double coincidence O6+ - summed over telescope and eoq (sorted sector)

This parameter is virtual. It is calculated by calling the function REORDER_DATA with the following input parameters: dJ_dc_o6plus_sum1, SECTOR_angle.

Differential flux, dJ/dE double coincidence O6+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_dc_o6plus.

[no plot] Error in the differential flux value double coincidence O6+.

[no plot] Full 3-D VDF in phase space density for double coincidence C+.

Phase space density value double coincidence C+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: DF_dc_cplus.

[no plot] Error in velocity distribution function value double coincidence C+.

[no plot] Full 3-D VDF in counts for double coincidence C+.

[no plot] Error in counts estimated assuming Poisson statistics double coincidence C+.

[no plot] Full 3-D VDF differential flux, dJ/dE double coincidence C+.

Differential flux, dJ/dE double coincidence C+ (Telescope 2).

This parameter is virtual. It is calculated by calling the function ARR_SLICE with the following input parameters: dJ_dc_cplus.

[no plot] Error in the differential flux value double coincidence C+.

  status_code: 200
  from_cache:  False
  revalidated: False
  is_expired:  False
  timeout:     30
  max_retries: 5
  user headers: None
  cached_session_options: None
  cache_key:   5efb37bfc8d75c9c
  cache_file:  ./data/CachedSession/spase/5efb37bfc8d75c9c.json
  cache_file_stat: 
    st_atime: Wed, 24 Sep 2025 23:14:04.191475 GMT
    st_mtime: Wed, 24 Sep 2025 23:14:04.331478 GMT
    st_ctime: Wed, 24 Sep 2025 23:14:04.331478 GMT
  Request Headers:
    User-Agent: python-requests/2.25.1
    Accept-Encoding: gzip, deflate
    Accept: */*
    Connection: keep-alive
    If-None-Match: W/"68d471be-532e8"
    If-Modified-Since: Wed, 24 Sep 2025 22:33:34 GMT
  Response Headers:
    Content-Length: 13839
    Server: GitHub.com
    Content-Type: application/json; charset=utf-8
    x-origin-cache: HIT
    Last-Modified: Wed, 24 Sep 2025 22:33:35 GMT
    Access-Control-Allow-Origin: *
    ETag: W/"68d471bf-532e8"
    expires: Wed, 24 Sep 2025 23:24:04 GMT
    Cache-Control: max-age=600
    Content-Encoding: gzip
    x-proxy-cache: MISS
    X-GitHub-Request-Id: AAB0:14C82:1A355C:1C3B6C:68D47B39
    Accept-Ranges: bytes
    Age: 0
    Date: Wed, 24 Sep 2025 23:14:04 GMT
    Via: 1.1 varnish
    X-Served-By: cache-msp11878-MSP
    X-Cache: MISS
    X-Cache-Hits: 0
    X-Timer: S1758755644.243302,VS0,VE47
    Vary: Accept-Encoding
    X-Fastly-Request-ID: 662fdb5679168ca5c921eec30d1c9fb247b99ea6